Automatic Generation of CNC Turning Program in AutoLISP on AutoCAD and its Software Simulation

سال انتشار: 1386
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 2,197

فایل این مقاله در 8 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

ICME08_030

تاریخ نمایه سازی: 27 آبان 1388

چکیده مقاله:

This paper, presents a software for automatic generation and simulation of CNC turning program. In the designed software, at first, a program written in AutoLISP, gets primary information and reads the profile drawing of the workpiece. Then, the program determines the tool motion paths. And then, it prints necessary data for regulating the simulation and the CNC turning codes, in two separate text files. In the next step, the CNC simulator program, gets input data from the first file, and regulates the primary graphical environment. At the end, this program simulates the CNC turning program existing in the second file. This software can be used in industry and can reduce the programming and production time and cost and also, the need for skillful CNC programmers. The efficiency of this software is tested by using it on several practical examples.

کلیدواژه ها:

نویسندگان

V Sabri

M.Sc. Student Manufacturing Engineering Group, Mechanical Engineering Department,University of Tehran, Tehran, Iran

A Mostafapoor-Asl

Assistant Professor Manufacturing Engineering Group, Mechanical Engineering Department,University of Tabriz, Tabriz, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • M. Kovacica, M. Brezocnika, I. Paholea, J. Balica, and B. ...
  • S. P. Kolluri and A. A. Tseng, "Simulation of CNC ...
  • D. P. Fenster, T. Carrier, "..On the direct programming of ...
  • D. Eichner P.E., Dr. C. Anderson P.E., D. Sly, "An ...
  • B. S. V. Prasad, "Designing programming station software for CNC ...
  • S. Mansour, "Automatic generation of part programs for milling sculptured ...
  • J. C. Choi, B. M. Kim, H. Y. Cho, C. ...
  • Tehran Internationl Congress on Man ufacturing Engineering (TICME2007) December 10-13, ...
  • R. S. Lee, Q. C. Hsu, and S. _ Su, ...
  • K. Cetinkaya, "A study of the microscopic deformation behavior of ...
  • S. B. Sim, S.T. Lee, and C. H. Jang, "A ...
  • X. D. Fang and M. Tolouei-Rad, "Rule-based deep-drawing process planning ...
  • S. B. Lippman and J. Lajoie: C++ Pimer - 3" ...
  • B. Stroustrup: C++ Programming Language - 3" ed., Addison Wesley ...
  • AutoLISP Programmer's Reference, AutoCAD Release 12 Vol. 10, Autodesk, Inc., ...
  • نمایش کامل مراجع