Experimental Study of Cylindrical Wire Electrical Discharge Turning (CWEDT) Process, Part 1: MRR

سال انتشار: 1386
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 1,735

فایل این مقاله در 13 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

ICME08_056

تاریخ نمایه سازی: 27 آبان 1388

چکیده مقاله:

In this paper, the effects and optimization of machining parameters on material removal rate (MRR) in Cylindrical Wire Electrical Discharge Turning (CWEDT) process is investigated. Material removal rate is chosen as the machining parameters to verify the process. In addition, power, voltage, pulse off time and spindle rotational speed were adopted for evaluation by Taguchi method. A L9(34) Taguchi standard orthogonal array is chosen for the design of experiments. The level of important of the machining parameters on the material removal rate is determined by using analysis of variance (ANOVA). The optimum machining parameter combination was obtained by using the analysis of signal to noise (S/N) ratio. The variation of material removal rate with machining parameters is mathematically modeled by using regression analysis method. Finally, experimental tests were carried out to identify the effectiveness of this proposed method.

کلیدواژه ها:

نویسندگان

M.J Haddad

Ph.D. Student, Manufacturing Engineering Group, Tarbiat Modares University, Tehran, Iran

A Fadaei Tehrani

Assist. Prof., Manufacturing Engineering Group, Isfahan University of Technology, Isfahan, Iran

A Mohammadi

Lecturer, Education Workshop Center, Isfahan University of Technology, Isfahan, Iran

N Nehzat

Assist. Prof., Manufacturing Engineering Group, Isfahan University of Technology, Isfahan, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • J.A. Mc Geough: Advanced methods of machining - Chapman and ...
  • T.A. Spedding, Z.G. Wang, "Parametric optimization and surface characteristio of ...
  • /E/ 25.09.1, Robofil 290(1999), Geneva, Switzerland. ...
  • J. Kozak, K.P. Rajurkar, S.Z. Wang, "Material removal in WEDM ...
  • T.A. Spedding, Z.Q. Wang, "Study on modeling of wire EDM ...
  • D. Scott, S. Bovina, K.P. Rajurkar, "Analysis and optimization of ...
  • D.F. Dauw, L. Albert, "About the evolution of tool Wears ...
  • A.C.M. Daniels, Philps, Eindhoren, "NC wire spark erosion-a survey", Ann. ...
  • _ Kinoshhita, M. Fukui, G. Gamol, "Study on EDM with ...
  • T. Tanimura, C.J. Heuvelman, "The properties of the servo gap ...
  • N. Kinoshhita, M. Fukui, G. Gamo, "Control of wire -EDM ...
  • Y.S. Tarng, S.C. Ma, L.K. Chung, "Determi nation of optimal ...
  • W.J. Hsue, Y.S. Liao, S.S. Lu, "Fundamenta geometry analysis of ...
  • C.T. Lin, I.F. Chung, S.Y. Huang, "Improvement of machining accuracy ...
  • J. Qu, A.J. Shih, R.O. Scattergood, "Development of the cylindrical ...
  • J. Qu, A.J. Shih, R.O. Scattergood, "Development of the cylindrical ...
  • M.I. Gokler, A.M. Ozanozgu, "Experimental investigation of effects of cutting ...
  • A.B. Puri, B. B hattacharyya, "An analysis and optimization of ...
  • R. Ramakrish nan, L. Karu namoorthy, "Surface roughness model for ...
  • Tehran Internationl Congress on Manufactu ring Engineering (TICME2007) December 10-13, ...
  • A. Mohammadi, A. Fadaie Tehrani and E. Emanian, 2005, "A ...
  • T. Masuzawa, M. Fujino, K. Kobayashi and T. Suzuki, "Study ...
  • T. Masuzawa, C.L. Kuo and M Fujino, "A Combined Electrical ...
  • T. Masuzawa and H.K. Tonshoff, "Three-Di mentional Micromachi ning by ...
  • T. Masusawa, K.Okajima, T.Taguchi, M.Fujino, "EDDM lath for micro machining", ...
  • B.K. Rhoney, A.J. Shih, R.O. Scattergood, J.L. Akemon, D.J.Grant, M.B. ...
  • R. Ramakrish nan, L. Karu namoorthy, R. sudhesh, C. Kayalvizhi, ...
  • Mohammad Jafar Haddad: Statistical analysis of the results of the ...
  • M.S.Phadke Quality engineering using robust design _ Prentic Hall Int. ...
  • نمایش کامل مراجع