a study on effect of process variables onfatigue and impact behavior and bead penetration of robotic MIG welded AA6061 aluminum alloy joints

سال انتشار: 1388
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 1,435

فایل این مقاله در 8 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

IIWC01_060

تاریخ نمایه سازی: 6 مهر 1391

چکیده مقاله:

Aluminum alloys forming to AA6061 have a wide range of desirable properties which are used in different industries such as aircraft industry and other aerospace structures. The effect of processing variables on fatigue life, impact energy and bead penetration of AA6061 joints produced by MIG robotic welding process was analyzed in the present study. Different samples were obtained by employing arc voltages of 20, 23 and 26 V, welding currents of 110, 130 and 150 A, welding speeds of 50, 60 and 70 cm/min. After finishing of the welding process, the mechanical properties of the samples were evaluated by means of fatigue and impact test at room temperature and the depth of weld penetration was measured in all of geometrical specimens. Results were clearly illustrated that when heat input increases, fatigue life of weld metal decreases whereas impact energy of weld metal increases in first and then drops significantly. A linear increase in depth of penetration with increasing welding current and arc voltage was also observed. The biggest penetration in this investigation was observed for 60 cm/min welding speed

نویسندگان

H.R Ghazvinloo

Department of material engineering, University of Semnan, Semnan, Iran

A Honarbakhsh Raouf

Department of material engineering, University of Semnan, Semnan, Iran

N Shadfar

Oghab Afshan Indust. & Man. Comp., Semnan, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • Ates H and Tirker M (1999) Determination of penetration with ...
  • Bakes H and Benjamin D (1979) Metals Handbook, Volume. 2. ...
  • Cavaliere P, Campanile G, Panella F and Squillace A (2006) ...
  • Cavaliere P, Squillace A and Panella F (2008) Effect and ...
  • Dawes CJ (1995) An introduction to friction stir welding and ...
  • Elangovan K, Bal asubramanian V and Babu S (2009) Predicting ...
  • Thomas WM (1991) Friction stir welding. Int. Patent Appl. No. ...
  • Ting W, Dongpo W, Lixing H and Yufeng Z (2009) ...
  • Tilbentci K (1990) MIG-MAG arc welding, Gedik Welding Co. Press, ...
  • نمایش کامل مراجع