Experimental Investigation On GFRP Composites Under High And Low Velocity Impact

سال انتشار: 1390
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 1,052

متن کامل این مقاله منتشر نشده است و فقط به صورت چکیده یا چکیده مبسوط در پایگاه موجود می باشد.
توضیح: معمولا کلیه مقالاتی که کمتر از ۵ صفحه باشند در پایگاه سیویلیکا اصل مقاله (فول تکست) محسوب نمی شوند و فقط کاربران عضو بدون کسر اعتبار می توانند فایل آنها را دریافت نمایند.

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

PPSRC2011_097

تاریخ نمایه سازی: 30 بهمن 1390

چکیده مقاله:

Impact response of glass fiber reinforced plastic (GFRP) composites is of interest in military, marine and structural applications. The overall objective of this work was to investigate behavior of GFRP composites of constant thicknesses under high and low velocity impact . 0, 10, 20 and 30 (wt %) E-glass chopped strand fibers were incorporated into polypropylene using an internal mixer and all of the specimens were injection molded into square plates of size 120×120×2 mm and rectangular impact bars in an injection molding machine. Izod impact tests were performed using an Izod impact tester on specimens with V-notches. The values of the notched Izod impact energy were obtained from each group of five specimens. A single stage gas gun in velocity range of 20-150 m/s and harden steel hemispherical tip projectile with diameter of 8.1 mm and weight of 11.34 g, was used to conduct high velocity impact tests. In all of GFRP composite specimens, energy absorption and ballistic limit velocity showed better performance than specimens without glass fiber. Moreover results showed higher values for specimens containing 20 (wt %) glass fiber. In the other hand energy absorption and ballistic limit of GFRP composites was found to be strongly affected by fiber weight fractions.

نویسندگان

M.M Zamani

Department of Mechanical Engineering, Semnan University,۵th km Mashhad Road,Semnan, Iran

A Fereidoon

Department of composite, Iran Polymer and Petrochemical Institute, P.O. Box ۱۴۹۶۵/۱۱۵,

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • (Iran) slandا PPS-2011 rم November 15-17, 2011 Kish م Proceedings ...
  • T. Cziga ny, Mater sci forum. 2005, 196, 3267-3272. ...
  • P. Pozzi, R. Taurino, T. Zanasi, F. Andreola, L. Barbieri, ...
  • W.N.Ota, S.C.Amico, K.G. Satyanayana, Compos Sci Technol. 2005, 65, 873-881. ...
  • L.Iannucci, D.Pope, eXPRESS Polymer Letters. 2011, 5, 262-272. ...
  • B.A. Cheeseman, T.A.Bogetti, Compos Struct. 2003, 61, 161-173. ...
  • P. Raju Mantena, R.Mann, C.Nori, J Reinf Plast Cpmp. 2001, ...
  • J.G. Carrillo, W.J. Cantwell, Mech Mater. 2009, 41, 828-838. ...
  • Fuping Yuan, Liren Tsai, Vikas Prakash, A.M. Rajendran, Dattatraya P. ...
  • نمایش کامل مراجع