Fabrication of aluminum based composite foam by PM route using the blowing agent CaCO3

سال انتشار: 1389
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 2,355

فایل این مقاله در 6 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

COMPOSIT02_148

تاریخ نمایه سازی: 24 مهر 1389

چکیده مقاله:

One of the major means to manufacture aluminum foams is forming a dense precursor material with powder metallurgical methods, wherein desired powders mixed with a blowing agent are consolidated by various routes i.e. axial compression, isostatic pressing, hot extrusion, rolling, etc. Then, resultant precursors will be subjected to foaming treatment. In this research, calcium carbonate, the foaming agents mostly used in meltbased methods, is used to fabricate Al-Si-SiC foam by PM route. Powder mixtures containing aluminum, silicon and silicon carbide and calcium carbonate powders, were subjected to cold uni-axial pressing and then hot extrusion at 450˚ C. Consequent precursors had cylindrical shape and their relative densities were from %90 to %98 of theoretical density. The precursors were foamed in a stainless steel cylindrical mold, at 850˚C for various time intervals. Density of foams produced varies in a narrow range of 0.508 upto 0.6 gr/cm3. The cellular structure also showed relatively uniform distribution of cells, with average diameter of approximately 154 μm. A foam sample was tested under uniaxial compressive load and compressive strength was 11.81 MPa accompanied by 4.803 MJ/m3 energy absorption.

نویسندگان

K Sardashti

Graduate Student, Technische Fakultät, University of Erlangen, ۹۱۰۵۸ Erlangen

A Mohammadpour

Graduate Student,

S.M.H Mirbagheri

Assistant Professor, Department of Mining and Metallurgy, Amirkabir University of Technology, Tehran, Iran

M Ghambari

Assistant Professor, School of metallurgy and materials Engineering

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • J. Banhart, Manufacture, Ch aracterization and application of cellular metals ...
  • H.P. Degischer, B. Kriszt, Handbook of Cellular Metals: Production, Processing ...
  • John Banhart, Aluminum foams for lighter vehicles, International Journal of ...
  • B. Sosnick, Foamlike Metal, in US Patent 255535016 _ 1951. ...
  • C. Kiorner and R.F. Singer, Processing of Metal Foams- Challenges ...
  • M. Shiomi, S. Imagama, K. Osakada, R. Matsumoto, Fabrication of ...
  • F. Baumgartner, I. Duarte, J. Banhart, Indu strialization of Powder ...
  • S. Esmaeelzadeh, A. Simchi, D. Lehmhus, Effect of ceramic particle ...
  • S. Asavavis ithchai , A.R. Kennedy, The effect of Mg ...
  • C. Korner, M. Arnold, R. F. Singer, Metal foam stabilization ...
  • Curran, D.C. , Aluminum Foam Production using Calcium Carbonate as ...
  • V. Gergely, D.C. Curran, T.W. Clyne, The FOAMCARP process: foaming ...
  • L.E.G. Cambroneroa, J.M. Ruiz-Romana, F.A. Corpasb, J.M. Ruiz Prieto, Manufacturing ...
  • Ibrahim, A.H., Effect of Material and Processing Parameters on the ...
  • I. Durate and J. Banhart, A STUDY OF ALUMINIUN FOAM ...
  • M.F. Ashby, A.G. Evans, N.A. Fleck, L.J. Gibson, J.W. Hutchinson ...
  • Kammer, C. 1999. WWW.ea. n et/e aa/ed _ _ ation/TALAT) ...
  • نمایش کامل مراجع