Effect of curing time on physical and mechanical properties of MIO/synthetic rubber primer as weld joint coating of gas pipeline

سال انتشار: 1394
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 729

متن کامل این مقاله منتشر نشده است و فقط به صورت چکیده یا چکیده مبسوط در پایگاه موجود می باشد.
توضیح: معمولا کلیه مقالاتی که کمتر از ۵ صفحه باشند در پایگاه سیویلیکا اصل مقاله (فول تکست) محسوب نمی شوند و فقط کاربران عضو بدون کسر اعتبار می توانند فایل آنها را دریافت نمایند.

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

ICCC06_214

تاریخ نمایه سازی: 25 بهمن 1394

چکیده مقاله:

The influence of curing time on adhesion and flexibility of a synthetic primer reinforced with different ratios of micaceous iron oxide (MIO) is the aim of this study. MIO particles in the vol. % of 2.2, 8.2, 17.2 and 30 were added to the synthetic rubber based primer. The coatings were applied on low carbon steel plates and also on 8 inch outer diameter steel pipes. The morphological properties of the coated primers was determined using an optical microscope. In order to evaluation of the curing time on adhesion of the primers to top-coat (cold applied tape) and also on steel substrate, sequence peel and cross-cut adhesion tests, was done. Cupping test in different times after applying the samples on steel substrates were employed to investigate the effect of curing mechanism on flexibility of the coatings. The experimental results, indicated that the completing of curing of the synthetic rubber based primer is too long in room temperature (more than 3 moths). Cross-cut test results revealed that, when the coatings were completely cured, no change was observed by adding different ratios of MIO. Peel adhesion test results, presented that adding 2.2 vol. % of MIO particles into the primer improved the adhesion of the primer to the upper layer tape. Also, cupping tests showed that the samples containing 2.2 and 8.2 vol. % of MIO pigments has not any negative effect on flexibility of the coated primers.

کلیدواژه ها:

Pipeline coating- Micaceous Iron Oxide- Peel adhesion- Cross cut adhesion- Cupping

نویسندگان

H. Erfaghi

Abadan Faculty of Petroleum Engineering, Petroleum University of Technology, Abadan, Iran

M. Farzam

Abadan Faculty of Petroleum Engineering, Petroleum University of Technology, Abadan, Iran

D. Zaarie

Technical Faculty, South Tehran Branch, Islamic Azad University, Tehran, Iran

I. Danaee

Abadan Faculty of Petroleum Engineering, Petroleum University of Technology, Abadan, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • Wilmott K. M., Coating and Thermal Insulation of Subsea or ...
  • Baghdachi J., Adhesion aSpects of polymeric coatings, FSCT, 1997. ...
  • Canadian Standard Association, CAN/CSA Z245.21 -10, 2010. ...
  • نمایش کامل مراجع