STRUT-AND-TIE MODELS FOR HEADED 1 BAR DEVELOPMENT IN C-C-T NODES

سال انتشار: 1391
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 1,676

فایل این مقاله در 19 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

ICCE09_137

تاریخ نمایه سازی: 7 مهر 1391

چکیده مقاله:

This study presents strut-and-tie models (STM) explaining the development of bond strength along bonded length together with anchorage by head bearing of headed bars. The anchorage at a head requires construction of a biaxial compressed nodal zone and bond resistance needs to use the concept of a smeared node. This model consists of a strut with the nodal zone at head for head bearing and fan-shaped stress field for bond stresses along the development length. This modeling clarifies interaction between head bearing and bond resistances where a bond transfers along the development length of headed bars is necessary for a smooth force flow. The experimental results For series of headed bars with relatively small area of plate heads are interpreted 1 by this proposed model

نویسندگان

Farhang Farrokhi

Assistant Professor, Civil Engineering Department, University of Zanjan , Zanjan, Iran

mehdi shahidi

Student, Civil Engineering Department, University of Zanjan , Zanjan, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • Capacity Design (CCD) Approach for Concreteه 3. Fuchs, W. Eligehausen, ...
  • Hong, S. G. (1994), "Consistent Truss Modeling for Bar Development ...
  • International Congress on Civi Engineering, May 8-10, 2012 "و Iran ...
  • Berner, D. E. and Hoff, G. C. (1994), "Headed Reinforcemet ...
  • Wallace, J. W. (1997), "Headed Reinforcemet A Viable Option, " ...
  • DeVries, R. A. Jirsa, J. O. and Bashandy, T. (1998), ...
  • DeVries, R. A. (1996), "Anchorage of Headed Reinforcemet in Concrete, ...
  • Bashandy, T. R. (1996), "Application of Headed Bare in Concrete ...
  • ACI-ASCE Committee 35 , (2002), _ _ ommendations for Design ...
  • Thompson, M. K.(2002), "The Anchorage Behavior of Headed Reinforcemet _ ...
  • Hong, S. G., and Mueller, P.(1996), _ Model and Failure ...
  • Hong, S. G.(1996), _ Model for Tension Bars in Reinforced ...
  • Hong, S. G. (2000), "Strut-and-Te Models and Failure Mechanisms for ...
  • Ashour, A. F. and Morley, C. T.(1996), "Effective Factor of ...
  • MacGregor, J. G. and Wight, J. K.(2005), Reinforced Concrete: Mechanics ...
  • Yun, Y. M. and Ramirez, J. A.(1996), "Strength of Struts ...
  • Sigrist, V. Alvarez, M. and Kaufmann, W.(1995), "Shear and Flexure ...
  • _ ACI Committee 318. (2005), "Building Code Requirements for Structural ...
  • Wallace, J. W. McConnell, S. W. Gupta, P. and Cote, ...
  • ACI-ASCE Committee 421.(1999), "Shear Reinforcemet for Slabs (ACI 42 _ ...
  • ACI Committee 408.(2003), "Bond and Development of Straight Reinforcing Bars ...
  • Comite Euro International du Beton, CCEB-FIP MODEL CODE, Thomas Telford, ...
  • Choi, D. U.(2003), _ ofHeaded Bars for Application in External ...
  • Choi, D. U. Hong, S. G. and Lee, C. Y.(2002), ...
  • نمایش کامل مراجع