ROLLER COMPACTED CONCRETE TENSILE STRENGTH

سال انتشار: 1388
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 2,161

فایل این مقاله در 5 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

ICCT01_074

تاریخ نمایه سازی: 19 شهریور 1388

چکیده مقاله:

Roller compacted concrete (RCC) presents a relatively recent development in the concrete technology of lowcement content for construction of dams, which in turn developed for application in concrete pavements of roads and storage yards, but with higher cement content. It is important to fully understand the characteristics and physical properties of concrete in order to predict the response of concrete structures. Compressive strength is used as a reference of the overall quality of concrete. For this reason, it is the principal property employed in the design of concrete structures. However, compressive strength is not the only characteristic influencing the behaviour of concrete structure and, in particular, gravity concrete dams where the determination of compressive, tensile and shear strength capacities is imperative. Those can be obtained using eitherlaboratory-cast cylinders or drilled cores or sawn blocks from a test section. This paper describes two tensile strength tests, namely, the direct tensile test and the splitting test were cylindrical specimens were casted and compacted using vibrating hammer following the soil approach method. Cylindrical specimens were prepared in two layers or lifts, and then the cylinders were cured in water for 90 days, to be subjected for different testing procedures. The obtained results were tabulated and discussed as relationships between direct tensile and indirect tensile versus compressive strength. The Splitting tensile strength has ranged between 8.4 to 14.0% of compressive strength, while direct tensile test results were lower than that of splitting tensile. Direct tensile test was more difficult to conduct for parent concrete than splitting tensile tests, and values obtained by it ranged from 5.1 to 9.2% of the compressive strength. The values of direct tensile strength have ranged from 55.0 to 76.0% of splitting tensile strength.

نویسندگان

S.Y Barony

Civil Engg. Department, Faculty of Engineering, Al-Fateh University, Tripoli, Libya

A.M ALI

Civil Engineering Department, Faculty of Engineering, Al-Fateh University, Tripoli, Libya

A.M Gilani

Civil Engg. Department, Faculty of Engineering, Al-Fateh University, Tripoli, Libya

M.J Rouis

Civil Engg. Department, National School of Engineers, University of Sfax, Sfax, Tunisia

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • M. R. H. Dunstan, [2007]. _ state of the Art ...
  • M. R. H. Dunstan, [2007]. _ state of the Art ...
  • T.P. Dolen & K .F Von Fay [1979]. _ Development ...
  • R.A Kline. [2003].:" International Symposium On Roller Compacted Concrete, Spain. ...
  • S.Y. Barony & T. S. Sifaw. [2002]. "Laboratory Study to ...
  • S.Y. Barony, J. M. Rouis, A. M. Mansor, T. S. ...
  • S.Y. Barony, J. M. Rouis, A.M. Manso. [2004]. "The potential ...
  • نمایش کامل مراجع