Structural and mechanical properties of powder metallurgical AA5056/15 vol% MoSi2 composites: Effect of the processing route

سال انتشار: 1391
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 1,635

متن کامل این مقاله منتشر نشده است و فقط به صورت چکیده یا چکیده مبسوط در پایگاه موجود می باشد.
توضیح: معمولا کلیه مقالاتی که کمتر از ۵ صفحه باشند در پایگاه سیویلیکا اصل مقاله (فول تکست) محسوب نمی شوند و فقط کاربران عضو بدون کسر اعتبار می توانند فایل آنها را دریافت نمایند.

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

IIAC02_038

تاریخ نمایه سازی: 12 اردیبهشت 1392

چکیده مقاله:

In this research, the effect of different blending procedures on structural and mechanical properties of PM AA5056 aluminum matrix composites reinforced with 15 vol% MoSi2 intermetallic compound particles is reported. Low energy cube blending and high energy ball milling were used for mixing the matrix and intermetallic compound powders. The resulted composite powders then were encapsulated and hot extruded to composite bars. The results confirmed the effect of ball milling on production of a finer distribution of the reinforcement in the matrix, and a higher strength and hardness of the composite in comparison to cube mixed powder. The interface between the matrix and the reinforcements was clean in both composites as confirmed by scanning electron microscopy. Fracture surface analysis revealed particle/matrix debonding and particle fracture as main failure modes of the low energy and high energy blended composites, respectively.

کلیدواژه ها:

Aluminum Matrix Composites ، Intermetallic compound MoSi2 reinforcement ، Mechanical properties

نویسندگان

Hassan Abdollah-Pour

Materials engineering department, University of Semnan, Semnan, Iran, Formerly PhD student in IUST and a CENIM visitor

M. T. Salehi

Iran Science and Technology University (IUST), Tehran, Iran

S. Shabstari

Centro Nacional de Investigaciones Metalúrgicas (CENIM), Madrid, Spain

M. Lieblich

Centro Nacional de Investigaciones Metalúrgicas (CENIM), Madrid, Spain

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • T.W. Clyne and P.T. Withers, An Introduction to ...
  • C. Badini, M. La Veccia, A. Giurcanu and J. Wenhui, ...
  • P. Prader and H.P. Degischer, Mater. Sci. Technol., 16 (2000) ...
  • M. Yamada and Y. Unakoshi: in Intermetallic Compounds, Nikkan Kogyo ...
  • H. Omura, T. Miyoshi, Y. Takahashi, J.G. Conley Strengthened ...
  • Aluminum Alloys, Y-W. Kim and W.M. Griffith eds., TMS, The ...
  • J.L. Gonzalez -Carrasco , F. Garcfa-Cano, G. Caruana and M. ...
  • C. Dfaz, J.L. Gonzalez -Carrasco, G. Caruana and M. Lieblich, ...
  • نمایش کامل مراجع