Evaluation of forging parameters on Al-7075 aircraft door bracket by simulation

سال انتشار: 1393
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 627

فایل این مقاله در 8 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

IIAC03_090

تاریخ نمایه سازی: 9 فروردین 1395

چکیده مقاله:

The purpose of this research is to achieve the optimal parameters for producing forged aluminium alloy 7075 aircraft door bracket by using finite element modelling (FEM) with commercial DEFORM-3D V6.1 and physical simulations with plasticine and Plexiglas dies. Also, forging speed has been examined as the main factor for controlling to produce a part without any defects. The results of Physical Simulation showed that the flow pattern has good agreement with the results of FEM that has been done based on the use of hydraulic presses with initial billet and dies temperatures 410 and 400 ° C, respectively, and different forging speeds 5, 10 and 15 mm/sec. distribution of effective strain rate, effective strain, effective stress, temperature , forging force and dies wear showed improvement the results in forging speed of 5 mm/sec. Processing map of Aluminium alloy 7075 also checked out at constant strain 0.5, indicated that thespecified area of the forged part is located in a safe area. Forging force in optimized forging speed 5 mm/sec showed that the forging process using a 1000-ton press can be done easily

کلیدواژه ها:

نویسندگان

e barati

Department of Material Engineering, Malek Ashtar University, Shahin Shahr, P.O. Box: 115/83145, Iran

kh farmanesh

Department of Material Engineering, Malek Ashtar University, Shahin Shahr, P.O. Box: 115/83145, Iran

a soltanpour

Department of Material Engineering, Malek Ashtar University, Shahin Shahr, P.O. Box: 115/83145, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • S.K. Biswas, W.A. Knight, Perform design for closed die basis ...
  • Y .H. Kim, T.K. Ryou, H.J. Choi, B.B. Hwang, An ...
  • Ron Cobden, Alcan, Banbury, " Aluminium: Physical Properties, Characteristics and ...
  • "Metals Handb ook-Forming and Forging", Vol. 14, 9th Edition, ASM ...
  • George E. Dieter, Howard A. Kuhn, S. Lee Semiatin, editors, ...
  • Akgerman, T. Altan, Recent developments in computer- aided design of ...
  • FLUHRER J DEFORMTN 3D Version6. User's Manual [MColumbus: SFT Inc., ...
  • Erman E.Semiatin S.L. "Introduction. physical modeling of metalworking processes" Phisical ...
  • forging load die wear", J of Material Processing Technology, V ...
  • Vesna Mandc and et.al."Physical Modelling And Fem Simulation Of The ...
  • Hasan Sofioglu, Hasan Gedikli, Jahan Rasty;" ...
  • - Physical Simulation results showed that the process of Technology, ...
  • technology for a comp lex-shaped light alloy forging" [J]. Journal ...
  • _ Flow pattern Cross section of plasticine by physical forging ...
  • simulation hs good agreement with the modl obtained (2006) 6676-6690 ...
  • mm/sec due to the distribution of strain rate effective TALAT ...
  • 04-0.9S-land temperature Range 415-427 "C , [16] Yongbiao Yang and ...
  • M. Raj amuthami Iselvan _ _ S. Ramanathan _ Hot ...
  • Y. Prasad and . Sasidhara:" Hot working guide: a ...
  • from FEM with experimental results has been performed International, 1997. ...
  • -FEM based on the use of hydraulic press at the ...
  • rate of 5 , 10 and 15 mm/s _ done ...
  • mm/sec due to the distribution of strain rate effective TALAT ...
  • نمایش کامل مراجع