The Effect of Pre-compaction on Dynamic Compaction Process of Al/SiCNanocomposite Powder

سال انتشار: 1392
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 929

فایل این مقاله در 8 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

WMECH02_056

تاریخ نمایه سازی: 21 تیر 1393

چکیده مقاله:

The effect of quasi-static pre-compaction on the mechanical and microstructural properties of Al7075/SiC and Al6061/SiC nanocomposites fabricated by dynamic compaction is investigated in this study. The increase in initial density by quasi-static pre-compaction plays an important role on properties of dynamic compacted metal powders. Pre-compaction is a useful operation in high velocitycompaction (strain rates 105s-1 to 107s-1) which can improve the green density of final compacted sample. However, it is shown in this work that pre-compaction of powder followed by lower strain rates compaction process (101s-1 to 103s-1)may lead to lower density, hardness, and even strength of the compacts. Damage and embrittlement were observed almost in all of the samples compacted initially before dynamic compaction. Investigations show that intensive cold work on pre-compacted samples may be one of the reasons of lower densification. Also, less free space between particles in precompacted specimens which may result in lower particles velocity and weaker bonding is believed tobe another affecting factor.

نویسندگان

G. H Majzoobi

Professor

A Atrian

PhD Student

H Bakhtiari

MSc, Mechanical Engineering Department, Faculty of Engineering, Bu-Ali Sina University, Hamedan, ۶۵۱۷۴, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • Tavoosi, M., et al. (2009), Bulk Al-Zn/Al2O3 nanocomposite prepared by ...
  • Khadem, S.A., et al. (2011), Structural and morphological evaluation of ...
  • Jafari, M., et al. (2012), Mechanical properties of nanostructured A ...
  • Ahmed, A., et al. (2010), Synthesis, Tensile Testing, and Micros ...
  • Oioro, J., et al. (2009), High -temperatu re mechanical properties ...
  • Mohanty, R.M., et al. (2008), Boron carbide- reinforced alumnium 1100 ...
  • Gourdin, W.H. (1986), Dynaic consolidation of metal powders. Progress in ...
  • Wang, Z., et al. (2010), Dynamic consolidation of W-Cu nanocompos ...
  • Fredenburg, D.A., et al. (2010), Shock consolidation of nanocrystalline 6061-T6 ...
  • Wang, J.Z., et al. (2009), High velocity compaction of ferrous ...
  • Yi, M.-j., et al. (2009), Comparative research on high-velocity compaction ...
  • Azhdar, B., et al. (2005), Development of a High-Velocity Compaction ...
  • Sethi, G.. et al. (2008), An overview of dynamic compaction ...
  • ASM Handbook, Volume 7, Powder Metal Technologies and Applications (1998): ...
  • Alizadeh, A. and E. Taheri-Nassaj (2011), Wear Behavior of Nanos ...
  • Dong, Y.L., et al. (2009), Fabrication and mechanical properties of ...
  • Canakci, A. (2011), Microstructure and abrasive wear behaviour of B4C ...
  • نمایش کامل مراجع