Investigation of Clamp Geometry Effects on the FractureCharacterization by Modified Arcan Fixture

سال انتشار: 1392
نوع سند: مقاله کنفرانسی
زبان: انگلیسی
مشاهده: 872

فایل این مقاله در 6 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

WMECH02_134

تاریخ نمایه سازی: 21 تیر 1393

چکیده مقاله:

This study presents investigation of clamp geometry effects on the fracture characterization of the materials by using modified Arcan fixture. In most applications fracture occurs in mode-I (tensile), mode-II (shear), or the combination of shear and tensile modes. In modified Arcan fixture by varying the loading angle,  from 0o to 90o, pure mode-I, pure mode-II and mixed mode data can be obtained. The test fixture and sample were modelled with ABAQUS/CAE and the contour integral method was used at various loading angles to calculate the non-dimensional stress intensity factors. To study the effect of mixed mode loading conditions, the fracture parameters were studied at loading intervals of 3o. By investigating the values of non-dimensional stress intensity factures, a non- uniformity is shown in the values of mode-II non-dimensional stress intensity factures close to pure mode-II loading. By investigating the influence of clamp geometry it was resulted that this non-uniformity was due to the geometry of modified Arcan fixture. This study also investigated the influence of deformation of fixture on the values of fracture parameters. Results showed that by reforming the geometry of modified Arcan fixture the non-uniformity was omitted.

نویسندگان

A Es'hagi Oskui

Postgraduate Student

N Choupani

Associate Professor

M Shameli

PhD Student Mechanical Engineering Department, Sahand University of Technology, Tabriz, Iran, P.O.Box: ۵۱۳۳۵-۱۹۹۶

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • Lawn BR, Wilshaw TR. (1975), Cambridge University Press. ...
  • Wilkins, D. J., Eisenmann, J. R., Camin, R. A., Margolis, ...
  • American Society for Testing and Material, (2007), Standard E399-06, Annual ...
  • Russell, A. J. (1982), DREP Materials Report. 82-0, Defense Research ...
  • O'Brien, T. K. (1984), ASTM STP 836, D. J. Wilkins, ...
  • Johnson, W. S. (1987), Journal of Testing and Evaluation 15(6), ...
  • Reeder, J. R. and Crews, J. H., Jr. (1990), AIAA ...
  • Bradley, W. L. and Cohen, R. N. (1985), ASTM STP ...
  • Russell, A J., and Street, K. N. (1985), ASTM STP ...
  • Hashemi, S., Kinloch, A. J., and Williams J. G. (1987), ...
  • Arcan, M., Hashin, Z., and Voloshin, A. (1987), Experimental Mechanics ...
  • Nikbakht, M., Choupani, N. and Hosseini, S.R. (2009), Materials Science ...
  • Greer, J. M., Galyon Dorman, S. E., Hammond, M. J. ...
  • Pucillo, G. P., Grasso, M., Penta, F. Pinto, P. (2011), ...
  • Es'hagi Oskui, A., Choupani, N. and Haddadi, E. (2013), Polymer ...
  • Maccagno, T.M. and Knott, J.P. (1991), Engineering Fracture Mechanics 38, ...
  • Shih, C.P. (1974), American Society for Testing and Materials, Philadelphia, ...
  • Hutchinson, I.W., Paris, P.C. (1979), Stability analysis of I-controlled crack ...
  • Gdoutos, E. E., Zacharopoulos, D. A. and Meletis, E. I. ...
  • نمایش کامل مراجع